The Official Coimbatore Offline Meet(G2G) Thread

[dual disc 200]

err...ji i think factory recommends 20 micron as standard gap....30mic is ok for high speeds ...this is what seniors have said based on their valuable experience...so its ok only..unless you hear a ringing noise from cylinder anyway if there is some problem with it do you think a good run-in can correct it?? i doubt it!! so dont feel sad abt it!! its good only!! i did not follow run in at all for my bike which is using a local piston thanks to my mech ...only good thing he did was sleeving it good with best clearance!!and for high clearence less run-in distance is enough

Ji..The Factory Clearance is 50 Microns I guess. I'd kept it a little tight cos, I can't live with a slapping noise, rather I'll do a good run-in & set it. Slapping noise & piston rattling is a ***** ji...considering the money spent!

[dpak89]

Ji..The Factory Clearance is 50 Microns I guess. I'd kept it a little tight cos, I can't live with a slapping noise, rather I'll do a good run-in & set it. Slapping noise & piston rattling is a ***** ji...considering the money spent!

is it?? i thought it was 20 mic...but still anything +/-10microns are only recommended....why did you go so tight...?? i fear the outcome in high rev speeds ! rings will blow very quickly ..isn't it ??

[dual disc 200]

is it?? i thought it was 20 mic...but still anything +/-10microns are only recommended....why did you go so tight...?? i fear the outcome in high rev speeds ! rings will blow very quickly ..isn't it ??

It will blow-out to everything inside out if not taken care properly ji. A good run-in for 3k kms on a good Synth 2T oil will solve everything & i'm pretty confident on that.

[dpak89]

It will blow-out to everything inside out if not taken care properly ji. A good run-in for 3k kms on a good Synth 2T oil will solve everything & i'm pretty confident on that.

ok!! let your idea go good!! but 3k kms will take lot of time to finish!! where do you suggest to go for ride then??

[dual disc 200]

ok!! let your idea go good!! but 3k kms will take lot of time to finish!! where do you suggest to go for ride then??

Here's where i go blank now....!

[dpak89]

Here's where i go blank now....!

hmmm...even i dont know what to suggest to you!! may be you can post it in the two strokes thread or in your own thread...surely good suggestions will pour in from our seniors!! i think distance is not a problem ..it's the way we drive!!so pls do ask for suggestions...

[Suru]

As far as my knowledge there is nothing much to do ji... Just about a tyre change & plug reading at regular intervals would suffice.

@ram: ji run in can be done even on our trip, its not a big deal coz if we maintain a specific rpm and specific speed with respect to the gear..nothing will do harm !! so i suggest you can definitely take your bike for a 500+km trip also..
@Suru:some points which i learned, before going on a trip in Rx are
1.chain sprocket/chain check.
2.spark plug/have spare plug also
3.carb tuning and cleaning.
4.all oil seals to be checked for leak.
5.brake cables and clutch cables check.
i think there are some more... but this is enough i hope ...and also you should have a tools kit compulsorily !!
Reg tire > for time being go for MRF rib ...it will be cheap.

Ji, all are new. oil bit leaking from fork. wil check out MRF.. Ji, all the above u said are new, but what is this new thing called tools kit.. wont 2 spark plugs and a spanner to remove that would suffice?????

True ji, but if you know my piston clearance, it'll bring you cold showers. 30 Microns...

err...ji i think factory recommends 20 micron as standard gap..correct me if i am wrong...then 30mic is ok for high speeds .....this is what seniors have said based on their valuable experience...so its ok only..unless you hear a ringing noise from cylinder anyway if there is some problem with it do you think a good run-in can correct it?? i doubt it!! so dont feel sad abt it!! its good only!! i did not follow run in at all for my bike which is using a local piston thanks to my mech ...only good thing he did was sleeving it good with best clearance!!and for high clearence less run-in distance is enough

is it?? i thought it was 20 mic...but still anything +/-10microns are only recommended....why did you go so tight...?? i fear the outcome in high rev speeds ! rings will blow very quickly ..isn't it ??

It will blow-out to everything inside out if not taken care properly ji. A good run-in for 3k kms on a good Synth 2T oil will solve everything & i'm pretty confident on that.

by the way, what are u guys talking about , sometimes, I go up to 60+ and all.. for the trip, shall i will maintain 50 with occasional 60s.. any problem technically????

[Naughty VaIsH]

who all are the others .. on the leh ride .. other than josh and karthik ?

[dpak89]

Ji, all are new. oil bit leaking from fork. wil check out MRF.. Ji, all the above u said are new, but what is this new thing called tools kit.. wont 2 spark plugs and a spanner to remove that would suffice?????

yea plug spanner is needed...also you need a cutting plier in case, your brake adjustment goes weak ...then you have to adjust it!!also screw drivers are needed!! it happened to me once when i was on a short trip my chain cover got loose and began to make huge noise, since chain was sliding with cover! i had a screw driver so i tightened it with another screw removed from mud guard...more the tools you take more advantage i say!! ..

by the way, what are u guys talking about , sometimes, I go up to 60+ and all.. for the trip, shall i will maintain 50 with occasional 60s.. any problem technically????

there are prescribed speeds for each gear ....pls post this doubt in two stroke forum and get the speed limit for each gear!! you should not cross this speed for your cylinder's safety!! i think in case of 100 max speed in run-in period is 40-50!! 60+ is a big NO

[dpak89]

@suru: check this post..one of a senior member has explained the spped shifts!! http://www.xbhp.com/talkies/thumpers...-bikes-43.html

[Suru]

Thanks Deepak ji, for posting on two-strokers thread.. I also asked him about the fit that they had put in.... They said its a "no problemo fit".. When I enquired if they had put in a tight fit, he started literally scolding me if someone would put a tight fit.. I also visited the lathe where they did the sleeve.. It surely does look good. They had a couple of computerized machines, plus Ram ji's mechanic also said that they are good. Its called D'silva machinary or something. He specializes only in cylinders and pistons thingie, especially bullets. actually was stunned to see some 100s of cylinders of all sizes and shapes kept there... The plan to Bangalore also flopped since it was almost 3 o'clock in the morning when I stepped out of the mech's shop.. Had to change the Fork Leg since oil was leaking and it was also damaged a bit.. So plans all due for next weekend... @Ram Ji: Click on the link in Deepak ji's post.. in the below post, you will see Shaolin's speedo.. Can see the gear indicator...

[dpak89]

can we have a meet this weekend? its been long time since we all have met!!

[dual disc 200]

can we have a meet this weekend? its been long time since we all have met!!

Done Ji..! Fix-up the place & we can have a Photo-shoot of the three 2 strokers too! Wat say?

[dpak89]

Done Ji..! Fix-up the place & we can have a Photo-shoot of the three 2 strokers too! Wat say?

super!! and please u fix an appropriate place where background for photo shoot can be good!! i don't know any place here literally!! phew!! so now i have to clean my bike again at least, to be visible in some corner in photos since ur beauty will be there!!

[dual disc 200]

super!! and please u fix an appropriate place where background for photo shoot can be good!! i don't know any place here literally!! phew!! so now i have to clean my bike again at least, to be visible in some corner in photos since ur beauty will be there!!

Ha..ha...! Let's take a call with Suru too ji! Since only three of us are here, will see what Suru has to say. I also think Suru has plans to Bangy this weekend.