-
^^Yes i am trying to get some knowledge about them.
I saw a few LED lights like LED STRIP, CIRCULAR LED LIGHT & BAR TYPE LIGHT. Can these be any useful to illuminate the console?Leave a comment:
-
^^ Nope, did not make one personally, but should not be too difficult to make one. Circuits will be available on the net.Leave a comment:
-
abhijeet what about digital flashers ? have you made any ? i saw one that auto sets blink rate and is made for leds as well as normal bulbs .that should save some battery power .Leave a comment:
-
^^Unfortunately, there is no easy way on this one. You have to fix a LED behind each digit on the meter and connect them properly thru resistors (and diodes if needed.)Leave a comment:
-
Console backlighting
Those LED's on the console look fantastic.
I too want to go for those white one's on my CBZ console.
Unfortunately i am a layman to the electronic world (management grad.)
Guys, Could you please tell a simple way that i could benefit from?
I think i have enough juice in the battery as my brakelights are allready LED's and I'm running on stock headlamp.
I asked my mechanic about this and he said that it was not possible and even if they replace the bulbs the glow would be insufficient.Leave a comment:
-
Originally posted by Shreeni0403 View Post
These flashers have a lower limit. When you cross that, the flasher will not blink but remain ON continously.
Making a custom one with a 555 timer IC is not too difficult!
You can search the net on this one!
Last edited by abhijeet080808; 03-04-2010, 10:52 PM.Leave a comment:
-
Let me clear it..!!
Bajaj's uses 21w flasher so front indicator 10w + rear 10w + console 1w = 21w
BUT
Honda uses 43w flasher, each bulb is 21w i.e front 21w, rear 21w and console 1w.
And someone said that i used capacitor, NO i didn't use any capacitor. Forget LED, why didn't it blink when I had put 10w bulb ??Leave a comment:
-
Normal bike blinker relay is rated to 21W, try to find a lower rated blinker module to use with an LED circuit or its even better to design a special circuit for this. Hope Abhi can do this easily.Leave a comment:
-
You must have used a capacitor in your circuit, so it was not blinking i guessOriginally posted by Shreeni0403 View PostWhether indicator will flash if we use LED's
This is bcz I tried putting a 10w bulb to save current (stock is 21w on Unicorn). Indicator didn't flash.
Tried LED, same thing happened. So how to put LED's so that it can consume 21w exactly !!!
Leave a comment:
-
21 w for 2 indicatorsOriginally posted by Shreeni0403 View PostWhether indicator will flash if we use LED's
This is bcz I tried putting a 10w bulb to save current (stock is 21w on Unicorn). Indicator didn't flash.
Tried LED, same thing happened. So how to put LED's so that it can consume 21w exactly !!! . the LEDs should have flashed ,though much faster rate .
Leave a comment:
-
Whether indicator will flash if we use LED's
This is bcz I tried putting a 10w bulb to save current (stock is 21w on Unicorn). Indicator didn't flash.
Tried LED, same thing happened. So how to put LED's so that it can consume 21w exactly !!!
Leave a comment:
-
In Pulsars there are two different rows of LEDs for Braking and Normal Tail lights.Originally posted by fayad555 View Post
SMD are also available as single units or can be removed from these strips, which then can be soldered to a pcb.
What I found out that, the pre-fabricated Resistors, are very reliable.Leave a comment:
Since '02 xBhp is different things to different people. From a close knit national community of bikers to India's only motorcycling lifestyle magazine and a place to make like-minded biker friends. Join us
Check engine oil level before every ride.
Our Partner
Leave a comment: