As I said in last page, its not a Bi-Xenon
Its Single Canon Dual Barrel
Hold on till this weekend, the ZMR will be up with DUAL TUBE HID aka Single Canon Dual Barrel which will be powered by double ballast

:d:d:d:d:d:d:d:d:d

.
abhi its time to try the migjhty 130/100,i am sure it will be no prob for your super strong system.

shree,when you are gettin bixenon for ur zmr?

if i get time,you never know,may be i shall ride down to bangy,YOU NEVER KNOW MAN!!!!!

@nano--
get the S@@t a&& battery replaced or break it on the delers head

guys..
i am back with a new re winded coil...
believe it or not, its more than 12 feet per pole...
every pole has the same number of turns...
except the first and the last pole which has around 10 winds less, as the yellow coil was bigger in size...

the worst part of the story is that I FORGOT MY CAMERA...
so i had to take pics with my friend's cheap mobile phone as my phone's battery was also dead...

i somehow managed to click some pics in extreme low light conditions, no matter how bad the pics are, i am still posting it...


here are the pics...












i didn't check the voltage output and also the amps as it was too late in the night when i returned home...

now comes a new trouble...
things are still the same..

battery dies even on the highways if headlight is on as when i was returning i had to come with lights dead...
horn doesn't sound at all...

i think my battery (which is not getting charged again) needs to be replaced...

am too busy today as well as tomorrow to do it,
besides i need to check the coil output also, which i might by tonight if i get time...

wiring is correct i cross checked, but still tonight, with a multimeter and enough time i can decide something concrete ...


Kismet hi kharaab hai meri

My HID's.. As I told you, hold on till the weekend
Hopefully my Single Canon with Double Barrel will put out the sh** out of the truckies.

I was talking about my halo and your HID!!

Are you planning to put HID?
Wish I could welcome Dr. with a little more than what he has
I would have done it if I had my Uni man !!

If you do ride down, you will get a warm welcome from a 100/90W bulb and a 4300k HID!

But can connect right before the relay

Dr. - Feeling to see your setup in LIVE action, why don't you ride down to Bangalore once
Even Abhi is in Bangalore now

No harm at all provided u should've enough space to take the 6A diodes within the switch assy. Am afraid to say the space will be minimum.

Arrey its the wire out of switch, from there it will go to relay !! So IN4001 is sufficient to drive relay, any harm using 6A4 to drive relay??

Shree, then where will u put the relays? After the stock switc? R u guys powering the HID directly from the stock switch or with a relay IN4001 will be driving the relay not the HID or even a halo Any doubts?

IN4001 will conk off. try the 6A4. Its rated at 6Amp so it's a safer choice!

Nano sir, nice snaps there...
Sorry I think I overlooked Dr's comments earlier.

Can you explain me the below BOLDED part clearly (IF YOU ARE NOT USING DIODES)
Is the setup as in the below diagram without any DIODE ?? If this is the case then when you put low or high BOTH the lights has to glow. Sorry if I have missed any of your posts.

Sajit, can IN4001 can take the load of HID or will the diode conk off ?

I think the 2nd attachment should be fine with DIODE.

idea is to have bixenon hid in reflector and hid in projector as well which will have dual beam with the help of shed,like sajjits...

planning to put just as mentioned as in the picture ,one upon one.
i really want to get rid of the shitty reflector of pulsars,the highbeam is tooo wide.

idea is both will have low beam and both will have high beam,but in this reflector the high beam is one of a kind,its tooo good,remember its the reflector that was useed in dcm toyota trucks,eicher trucks and also in contessa classic,so throw and beammming is really good.