Re: Honda Unicorn Dazzler

I have been using my dazzler over 3.5yrs and its going good . I recently got the pressure volves changed 3 months back since I am facing starting problems. During Cold start and hot start. I still have the issues with bike for it.

Then after these got changed, I realized that the engine is forming a residue over it. Its been there from some time. is the engine oil leaking? or what problem is it.
Also the machine made about 33k Km. I am steadily getting a mileage of 55 to 60kmpl. When should i Change my tyres.

Re: Honda Unicorn Dazzler



Any one knowa from where I can this disc and the caliper mounting ?

Sent from my GT-I9500 using Tapatalk

Re: Honda Unicorn Dazzler

^^ adjust clutch lever free play. Even if its within limit you can still adjust it and see if problem persists.

Re: Tyres

[MENTION=67830]Dccet[/MENTION] the chain slack is in the limits. I don't think its causing problem

Others please help

----consecutive posts auto-merged-----
[MENTION=67830]Dccet[/MENTION] the chain slack is in the limits. I don't think its causing problem

Others please help

Re: Tyres

Check drive Chain : Adjust slack, clean and lube

Re: Tyres

Query
1)The bike gear shifted from 1st to neutral from a stop>1st gear>neutral on its own. Is the clutch plate having some problem???
2)The bike pulls up with a slight jerk never experienced before, in stop-go traffic.
What is wrong with the motorcycle??? Please help
Note-Engine oil is about 300-400 Kms old (Shell AX-7 semi-synthetic 10W40)

Re: Tyres

Has any one done any modifications for cone set mine wares off very fast i am on my fifth set and its very irritating because the handling goes for a toss

----consecutive posts auto-merged-----

Has any one done any modifications for cone set mine wares off very fast i am on my fifth set and its very irritating because the handling goes for a toss

Re: Tyres

I don't know, but in Delhi you can get parts over counter. (That's at service center)
but mostly they are unavailable (so arranged it from two ASS)

even I had to struggle for that.

I inquired about parts to dealer and he said "its not available, we will request and arrange it for you by next week"

so I inquired on phone every week, It didn't help, they even stopped entertaining me on phone.

finally after 3 weeks I visited SVC again, and the first question they asked me was.. "Have you requested any part and payed in advance",

I was stumped, how could I if you don't tell me the procedure then itself.

I paid good 1K (as they were not sure of the cost) as advance (got a payment slip), then collected the part after two weeks.

That part (meter cover) cost was only in order of some ~INR250, got rest of ~750 back with part on showing that advance receipt.

Re: Tyres

I echo plasmabhai's words. I'm running on 120 vyde currently and did 7k so far. No issues with fitting.


Sent from my SM-N750 using xBhp Connect mobile app

Re: Honda Unicorn Dazzler

Few ASS supply spares over the counter and few do not. In Chennai for example, KUN honda at Adyar supplies spares over the counter.

Sent from my SM-N750 using xBhp Connect mobile app

Re: Tyres

I hate Honda ASS,I placed at a different ASS and few days later i went to check whether it has arrived and they suggest I check at other ASS also and suggest one near andheri. There is apolicy of these stupid ASS that they will not issue parts over the counter so you have to buy and get it fixed at the same place.

Damage to the wallet is as follows
1) Front cowl- Rs.145
2)Headlight frame-Rs.364
3)front screen-Rs.230
4)R.H.S turn indicator-Rs.217
I requested/argued about their stupid policy but to no avail...
Thanks @shail016 for your help

----consecutive posts auto-merged-----

Re: Tyres

Am running Vyde since last 12000 kms. So, yes there is enough clearance between chain and tyre. It is completely stock replacement - absolutely zero modifications.

My front cowl was similarly damaged. I wet sanded the damaged side of the panel by 1500 grit sand paper so that it was as smooth as possible. Then applied a matt black vinyl sticker over the complete damaged side from a road side sticker shop. Looks like stock, the sticker is difficult to make out even on close inspection - and total hit to the wallet? Rs.20/- :P

Re: Tyres

Let me try my bit


The center cowl has two plastic pins which holds the meter cover shown below.

The meter cover slides into those pins (at the red marked area), there are also rubber rings/dampeners inside the marked cavities.
also the cover head (the component which surrounds the entire console parameter) can also be detached from meter cover (after removing screws from the area marked in blue in above and below images)



So to remove the meter cover you need to first remove the screws from green marked area, and then (the hard part comes) pull the meter cover in such a way that you dont break anything. (its easy to slide in again)

For the glossy part you are referring you can see the inside structure below:



The portion connecting the 1st screw from the LHS in the picture actually slides inside the casing, but the screw is visible from the outside.

Instead I would say disconnect all the wiring and remove the headlight assembly (detach it from bike) and then remove the parts individually. Removing all the screws and stretching the entire mold might remove it easily . This way you can open screws present inside and easily remove any other attached part. This may also reduce any chance of accidentally breaking any lock or screw holder.

hope it helps.

Re: Tyres

@shail016
Thank you for the pictures of the parts.I tried opening the assembly but could not figure out how to remove the front cowl the metallic painted part I tried pulling moving it around but could not remove it.

It would be really great if you could try to write down how you did it

I removed all the screws but still was not able to remove it

----consecutive posts auto-merged-----

Re: Tyres

Yes I did, I live in Delhi but I obtained parts from gurgaon (Ganpati honda), and replaced them myself (its easy).

please ref this post for price then: http://www.xbhp.com/talkies/motorcyc...ml#post1042967

and this post for the headlight components: http://www.xbhp.com/talkies/motorcyc...ml#post1046219

Hope it helps.