Let there be Light : Bike Lighting, HID etc

[captainofv]

How to align the aim of projector high beam vertically ??

Hi,
Recently I have installed projector headlights to my new bajaj v, but the problem is the aim of white high beam light is too high.
I have asked the mechanic to adjust the light but he was not able to do that and told me may be showroom mechanic can do that without removing the whole headlight.
So,please suggest me how to do the alignment vertically because I am not able to use the high beam as because it may blind drivers from opposite side.

[BikerKid]

Re: Let there be Light : Bike Lighting, HID etc

can i plonk an 55/60 w halogen in my pulsar 135? i have replaced the pilot lamps and no plate lamp with leds! do these led headlights come in 35-40 w and 4300k spectrum? i don't want to go with anything over 4500 k. i guess hid initial amp draw is huge and then it works better in a projector, right? how much will and hid with projector cost? a bi-xenon with both hi and low hid beams?

[leech]

Re: Let there be Light : Bike Lighting, HID etc

The difference is very marginal, it will reduce the hit of high beams from oncoming traffic but not eliminate. I used this bulb and after 15 days of usage I switched back to the stock bulb, the throw is very whitish which does not help in rainy season at all.

Cheers,
Sanjay

Aww, I already ordered one. Thanks anyway..

[emanoj]

Re: Let there be Light : Bike Lighting, HID etc

Hi Xbhpians!
I just want to know can I install LED H4/HS1 20w/20w Headlamp in my Yamaha Fazer v1, currently running both headlamps on in both upper and lower.
Thanks.

Link: NAO Brand Motorcycle LED Headlight H4 hi lo 20W*2 2000LM*2 HS1 COB ATV Head lamp 6500K White Standard High Low DC12V #M4-in Headlights from Automobiles & Motorcycles on Aliexpress.com | Alibaba Group
[ATTACH]214701[/ATTACH]
[ATTACH]214700[/ATTACH]
[ATTACH]214702[/ATTACH]

I've used the same headlamps. The output is good but white light easily gets diffracted when there is light from oncoming vehicles making it useless. Please check my earlier posts buddy and decide based on that.

[Skanda]

Re: How to get dismantle RE Lucas headlight?

thanks, heat gun will work for modern fiber/pastic domes. What I have here is an Iron dome. I have not tried heating it, may be I should give a try. However, I'm concerned expanded metal will break the glass.

I didn't think about that, if that's iron dome, I'm not sure how that works.

[Skanda]

Re: Let there be Light : Bike Lighting, HID etc

Hi Xbhpians!
I just want to know can I install LED H4/HS1 20w/20w Headlamp in my Yamaha Fazer v1, currently running both headlamps on in both upper and lower.
Thanks.

Link: NAO Brand Motorcycle LED Headlight H4 hi lo 20W*2 2000LM*2 HS1 COB ATV Head lamp 6500K White Standard High Low DC12V #M4-in Headlights from Automobiles & Motorcycles on Aliexpress.com | Alibaba Group

If I'm not wrong, as your headlight output is not dependent on throttle, it's just plug and play. Remove the old bulb and install this, that's it.

[Ankur9468]

Lights for Apache R.T.R.160 For Night Driving

Suggest me Front Lights for Night Driving.
Please give detailed information if possible.

Price
Model
Availability
Installation
Impact on battery
Anything else


THANKS in advance.

[sanjaysangar1990]

Re: Let there be Light : Bike Lighting, HID etc

Hi, how does the Phillips extreme vision perform on the CBR? Does it give any advantage over the stock bulb when blinded by incoming traffic?

The difference is very marginal, it will reduce the hit of high beams from oncoming traffic but not eliminate. I used this bulb and after 15 days of usage I switched back to the stock bulb, the throw is very whitish which does not help in rainy season at all.

Cheers,
Sanjay

[saikatbyte]

Re: Let there be Light : Bike Lighting, HID etc

Hi Xbhpians!
I just want to know can I install LED H4/HS1 20w/20w Headlamp in my Yamaha Fazer v1, currently running both headlamps on in both upper and lower.
Thanks.

Link: NAO Brand Motorcycle LED Headlight H4 hi lo 20W*2 2000LM*2 HS1 COB ATV Head lamp 6500K White Standard High Low DC12V #M4-in Headlights from Automobiles & Motorcycles on Aliexpress.com | Alibaba Group

[nidclt]

Re: How to get dismantle RE Lucas headlight?

You can do that by using heat gun. We usually separate the glass form the reflector while installing HID projector headlights. Check this video out -> https://youtu.be/W6UvaSYdeDo. Be sure to seal it tight by using same sealant or use mseal to make it Waterproof.

thanks, heat gun will work for modern fiber/pastic domes. What I have here is an Iron dome. I have not tried heating it, may be I should give a try. However, I'm concerned expanded metal will break the glass.

[Skanda]

Re: How to get dismantle RE Lucas headlight?

Hi guys, I am restoring my '75 bullet. I got original Lucas headlamp from olx. But the steel reflector is rusted and need to be replaced. It is attached to the glass. Does anyone know how to get this apart without damaging England made glass, so that I can either electroplate the existing dome or change to a new one.
I checked with the local electroplating shop, they said the glass definitely need to be removed before plating.

You can do that by using heat gun. We usually separate the glass form the reflector while installing HID projector headlights. Check this video out -> https://youtu.be/W6UvaSYdeDo. Be sure to seal it tight by using same sealant or use mseal to make it Waterproof.

[nidclt]

How to get dismantle RE Lucas headlight?

Hi guys, I am restoring my '75 bullet. I got original Lucas headlamp from olx. But the steel reflector is rusted and need to be replaced. It is attached to the glass. Does anyone know how to get this apart without damaging England made glass, so that I can either electroplate the existing dome or change to a new one.
I checked with the local electroplating shop, they said the glass definitely need to be removed before plating.

[leech]

Re: Let there be Light : Bike Lighting, HID etc

Go for Philips Extremevision, best of the lot. Am using on my CBR, VERSYS & Ecosport and thoroughly happy.

Hi, how does the Phillips extreme vision perform on the CBR? Does it give any advantage over the stock bulb when blinded by incoming traffic?

[r0rshack]

Re: Need to install cyclops h4 led 3800 lumens in Apache RTR 180 abs new

Guys, can i know someone's experience of using the bright LED lamps in Rainy conditions? how much does it really help? Also, would tinting the white light to Yellow be of any use in Rain?

How would a T10 LED pilot lamp work?

Buddy, i dont know about RTR180 ABS, from your description, it looks like DC..,
but for the LED's, DC is not essential They would run, but do not run fine. I used 30 rupees T10 1W SMD LED's on my GS150r and they worked for some time(maybe for 2 weeks).. i could notice them flickering becos of the AC.
On the other hand i used another T10 3W LED's which lasted only for 2 days. The problem being, the resistor couldn't handle the current, burnt and later failed the LED.
so, using the LED headlight directly on AC might light up the LED..but could go kaput really soon.(haven't tried this! )

[vivekgautams]

Re: Need to install cyclops h4 led 3800 lumens in Apache RTR 180 abs new

Hello guys...
I want to install cyclops h4 led light in my rtr 180 abs new .
It is mentioned that cyclops led will work only on dc.. I don't know that my bike has a dc supply to the headlight or ac. How can i check that.?

The RTR180 ABS is D.C for sure. The LED will work fine.
The pilot light on my bike are led. I'v installed and used HID on my bike, no problems.
I have tested my friends "cree" LED H4 on my RTR180 ABS before he installed the led on his CBR150r. Worked fine!

Apache's are still relying on ac circuits. No dc mechanisms from tvs till date.

Bro, IF RTR180 ABS was AC (and without any electrical mods) .. How would a h4 H.I.D work fine on A.C? How would a T10 LED pilot lamp work? How does a "CREE" h4 LED bulb glow the same on a RTR180 ABS and a CBR150R, with the engine off (CBR150R also AC?) ?
Buddy, I'm no Electrical/ Electronics engineer.. Please help me understand the results of my experiments/observations/experience with my RTR180 ABS.

Cheers!