Hii

it is 298 mm disk !

it's a custom item and not form any of the bikes ..

it costed me Rs850 incl shipping !

i baught it from sniper automotives !

^^Hey Viv,

Sorry my ignorance but what bike is this? Unicorn?

And what all modifications are required to fit this bigger disc? and is there any appereant difference in the stopping prowess of bike?

bike is unicorn v1 .

rotor is direct fit and mounting plate needed good amt of precision work.

it was a time consuming to design plate but at the end mounting plate was built.

BUT the rotor i was shipped has bends so the disk is not working currently.

well same i though as well..n nmany members here suggested NOT to go wid it..so i cancelled it... thanks for your suggestion brother...

n BYe the way..Ur bike looks awesome..

I was wondering how the classic headlight on the latest p180 (UG4) would look.. i just did some rough Photoshop work and here it is!

Looks awesome dude. Way better than stock headight!!

hey try the same on a p220 minus the fairing or 200

Dude it will luk the same,it only thing seperating the 220 from the other pulsars is the fairing, remove that and all the pulsars nearly luk the same & thats the reason i still have the fairing on my bike otherwise i would have got rid of it a long time ago for weight reduction

cmon, what is the cosmetic difference bet P200 and P220 if we leave fairing apart.

hey this is lil bit modification if liked plz. reply thx,.

Installing Angel eyes!

Hello Puneet!

I will make a basic post of this in the thread as well!
Separating the dome of the FZ from the clear glass is a rather easy task:
Things you will need to separate the dome:
1. A Oven(not microwave)
2. Leather Gloves.

Method:

Take the headlight assembly and remove all wires, screws, specially the stickers behind (eg, QC PASSED)
Now take a Aluminum foil and place it on the tray of the oven and place the headlight assembly on it.
light up your oven and close the Lid.
Set your timer or stop watch to 7 minutes and wait near the oven while the process takes place to make sure nothing goes wrong.
Once its 7 minutes wear your gloves and switch the oven OFF and carefully take your headlight assembly out and place it on a clean cloth or a cardboard.
Now with one hand pull the locks up and pull the headlight dome and the clear glass apart, you will notice it comes out easily and quickly, do this till you remove and completely separate the dome from the clear glass.
Install your angel eyes. (DO NOT USE SILICON or ANY TYPE OF GLUE TO STICK YOUR Angeleyes, it will severely damage the dome)
best thing to make the angeleyes sturdy is to drill 3 small holes in such a place that once the angel eyes are fitted, the holes will be hidden.
Use the top 2 holes to secure the wires and the lower hole to pass a small fishing line( fishing line is a transparent type of high strength thread, which is used for fishing) lollz (sorry that was funny)
Once secured, connect your angel eyes to the parking light connection and CHECK (you will be sorry if it does not light up later after fitting it back inside)

Fixing back the Dome to the Clear glass

Method:

1. Take the dome and put it in the oven and light up your oven and keep the dome inside for 1 minute to 1'30" maximum.
2. Carefully after cleaning, place the clear glass on it and press till the locks "tick" in place.
3. Allow it to air cool for 30 minutes.

That is how I installed my angel eyes, I hope this answers all your questions about installing the eyes by your own!

Any more queries or biking problems, I'd be glad to help if I have knowledge about it!

Regards,

Roadfreak!

i was looking for this kinda explanation very thanksss to you..

You're welcome dude!

Dude dont u use ur bike at nights !!Wat bout ur headlights

No indicators ??
No plate ??