Tweet
Originally posted by ani_ankush73
View Post
-
hyosung comet 250... -
guys i have a pulsar 180 ug3 180 cc , it has 43t sprocket , i need it to downsize it to 41 teeth my mechanic told me that 1gen unicorn sprocket is direct fit for pulsar
can any one confirm the same and what will be it cost??Comment
-
1st/2nd Gen Unicorn has 42T rear and 15T front. You wont get rear sprocket as spare, you gotta buy full kit which will cost around 800rs.Originally posted by r@m View PostComment
-
FZ16 sprocketing
Hi all,
I've been looking for a while to gear up my FZ since it's standard gearing is quite low. I always feel I'm in 4th gear when I'm in 5th!
I was hoping to change the front to 15T or the rear to 38T. Standard are 14/40.
A mech had a look at the front sprocket and he's not sure a 15T sprocket would fit in the available space.
Has anybody here already tried other options? Does anyone have any ideas?
@shreeni
do you know what pitch chain the FZ uses? Is there anyway to find out without having to measure with a vernier?Comment
-
Help needed in Sprocketing my Karizma
I was thinking abt doing sprocketing in my Karizma . I am basically a tourer and like to keep my bike at higher Rpms /speeds continuously long hours a day. Can any one tell me your experience with sproketing?
is the difference noticable? please note that other than iridium spark plug and Michelin M 45 i idnt doen any other modifications. How much sprocketign will cost me ? i am planning to reduce rear by two teeths and no change in front sprocket.
so what will be total cost for this?
SHould i buy a new chain ? or stock chain will do ? or of not which chain and which bikes sprocket should i buy ?
will the top end increase noticable?
did your accelration decreased much ?
any difference in mileage?
Please advice..sigpicComment
-
I am not sure what pitch chain FZ has but have a simple solution for you.Originally posted by iamvik View Post
If the chain pitch is 520 i.e like Karizma, Pulsar 200,220,180(UG4) then you can opt for P200 rear (38T), P220 DTSi (36T), P220 DTS Fi (37T).
If the chain pitch is smaller as in Unicorn and other bikes then you can opt HH Ambition (38T)
Thou am not sure about fitting on sprocket hub but customizing the holes wont be a problem.Comment
-
Thanks! I hadn't realised that those bikes have such size sprockets. Will definitely try them as soon as the next service is done.Originally posted by Shreeni0403 View PostI am not sure what pitch chain FZ has but have a simple solution for you.
If the chain pitch is 520 i.e like Karizma, Pulsar 200,220,180(UG4) then you can opt for P200 rear (38T), P220 DTSi (36T), P220 DTS Fi (37T).
If the chain pitch is smaller as in Unicorn and other bikes then you can opt HH Ambition (38T)
Thou am not sure about fitting on sprocket hub but customizing the holes wont be a problem.Comment
-
How did ur sprocketing experiment go, im still waiting for the verdict...Originally posted by Shreeni0403 View PostI am not sure what pitch chain FZ has but have a simple solution for you.
If the chain pitch is 520 i.e like Karizma, Pulsar 200,220,180(UG4) then you can opt for P200 rear (38T), P220 DTSi (36T), P220 DTS Fi (37T).
If the chain pitch is smaller as in Unicorn and other bikes then you can opt HH Ambition (38T)
Thou am not sure about fitting on sprocket hub but customizing the holes wont be a problem.Comment
-
Not yet done. I'm planning on getting the next free service done next week. I want to do a "before and after" test with the sprockets.Originally posted by rookster View Post
I measured the pitch with a simple ruler and I found it to be 12,5 mm. This means that the chain is either a 425 or a 428 (the most common size for small Indian bikes). I think I will try a 15T front sprocket or a 38T rear sprocket.
I will report back here once it's done.Comment
-
Hey can anyone tell whats the rear sprocket teeth number of Suzuki Shaolin ?????
Also theres another problem,u may find certain tooth sprockets in the market but that sprocket has to fit ur rear wheel.Sometimes the screw drills are bigger and they are not centred correctly.Is it possible to weld and redrill the sprockets while reboring it for the centre??Hell's Angel
sigpic
Comment
-
Under geared Stunner
Hi ... Currently i own 2010 CBF stunner....And feels under geared....im desperately looking for a sprockets change ...Will Stunner FI sprockets work....or any other.....option available ... please suggest ...also the price ...for entire Mod..... Thanks
Comment
-
What is your current sprocket count both front & back ??Originally posted by torque_lover View PostHi ... Currently i own 2010 CBF stunner....And feels under geared....im desperately looking for a sprockets change ...Will Stunner FI sprockets work....or any other.....option available ... please suggest ...also the price ...for entire Mod..... Thanks
Please let us know then we can think of giving some alternativessigpicAll India Permit 1+1Comment
-
Originally posted by abhilashabhi12 View Post
I have no idea about the exact count for front and rear... i searched and found no info with respect to count....Even the first page of this thread does not say about ...Honda bikes.......
Comment
-
i think stunner should be having same teeth similar to shine
it should be 14/41 or 42Comment
-
FZ sprocket change
I just had fitted a 15T front sprocket from the Unicorn to my FZ.
Will update with figures later.Comment
Comment