Since '02 xBhp is different things to different people. From a close knit national community of bikers to India's only motorcycling lifestyle magazine and a place to make like-minded biker friends. Join us

Axor
Magazine
Castrol Power 1

Check the helmet from inside.

Our Partner

Announcement

Collapse
No announcement yet.

Should I go for a Suzuki Shaolin?

Collapse
X
Collapse
 
  • Page of 15
  • Filter
  • Time
  • Show
Clear All
new posts
Previous 1 3 4 5 6 7 8 9 10 11 12 13 15 template Next
  • #106
    will try find out about a rear sprocket for the shaolin.. i replaced mine around 2 years ago.. am using a fiero chain on it now.. which is thicker.
    might make sense if you do the same.

    i assume your front sprocket is all ok?

    Comment

    • #107
      Currently the front one too is in bad shape

      The Fiero has a 13T - 40 T combo thats one less in the front and one more in the back do u think this is equal to 14T-39T

      to simplify

      Is 13T - 40T = 14T - 39T ??
      http://www.youtube.com/watch?v=yjWXI8T2HUM
      ---------------------------
      07' Pulsar 200 DTS-i
      99' Suzuki Shaolin
      85' Royal Enfield Bullet 350 (Sold)
      86' Ind-Suzuki Ax 100 (Sold)
      03' HH Splendor

      Comment

      • #108
        Originally posted by Nikhil Pereira View Post

        Is 13T - 40T = 14T - 39T ??

        Let me simplify.

        Is 40/13 = 39/14?

        A simple calculator should give you the answer
        Yamaha RX165 5-Speed
        Yamaha RD350
        HH Karizma
        Honda NSR150SP

        Comment

        • #109
          the first answer is 2.78

          the second one is 3.09

          2.78 = (is not equal to) 3.09

          but then its impossibble to find the 14 - 39 set up wat to do with the chain sprocket prob then????
          http://www.youtube.com/watch?v=yjWXI8T2HUM
          ---------------------------
          07' Pulsar 200 DTS-i
          99' Suzuki Shaolin
          85' Royal Enfield Bullet 350 (Sold)
          86' Ind-Suzuki Ax 100 (Sold)
          03' HH Splendor

          Comment

          • #110
            Just find a ratio that has the number closest to the one you desire, which i guess is 14/39. Then get the sprockets of that size. or do it in reverse.
            Yamaha RX165 5-Speed
            Yamaha RD350
            HH Karizma
            Honda NSR150SP

            Comment

            • #111
              @ sunni boi thanx for making me realise the ratio aspect here, dint strike me. . .yes brother ure rite. . .thanx a ton, wen i reach home today i shall get cracking with the calci.
              http://www.youtube.com/watch?v=yjWXI8T2HUM
              ---------------------------
              07' Pulsar 200 DTS-i
              99' Suzuki Shaolin
              85' Royal Enfield Bullet 350 (Sold)
              86' Ind-Suzuki Ax 100 (Sold)
              03' HH Splendor

              Comment

              • #112
                should be able to get the rear sprocket will try do some searching during the weekend..

                also wrt mirrors.. if you're going for the stock look you hould be able to get the samurai's mirrors.

                but imo they don't really gel with the look of the bike. i did a LOT of searching a few years ago, and finally decided on the splendor mirrors for hte bike. they go really well with the setup i have.

                Comment

                • #113
                  Well I,m going in for a 13 - 39 fiero setup, buying it tomorrow. and will look for a local 14T front sprock from a local dealer.

                  STILL NEED A DAMN PISTON. Almost all my troubles are solved except the piston kit one. All kinds of bearings and stuff too i ve manged to get. just waiting for next months pay to pick them up.
                  http://www.youtube.com/watch?v=yjWXI8T2HUM
                  ---------------------------
                  07' Pulsar 200 DTS-i
                  99' Suzuki Shaolin
                  85' Royal Enfield Bullet 350 (Sold)
                  86' Ind-Suzuki Ax 100 (Sold)
                  03' HH Splendor

                  Comment

                  • #114
                    Originally posted by ShaolinRider View Post
                    should be able to get the rear sprocket will try do some searching during the weekend..

                    also wrt mirrors.. if you're going for the stock look you hould be able to get the samurai's mirrors.

                    but imo they don't really gel with the look of the bike. i did a LOT of searching a few years ago, and finally decided on the splendor mirrors for hte bike. they go really well with the setup i have.

                    Thanx dude. Am trying to get in touch with this narang or amba tvs place. Hopefully weel get down some stickers, wat about the red stickers u had got dude?

                    Wat ever help you can give me will be great, As you can see from all my recent posts i desperately need a stock standard PISTON
                    http://www.youtube.com/watch?v=yjWXI8T2HUM
                    ---------------------------
                    07' Pulsar 200 DTS-i
                    99' Suzuki Shaolin
                    85' Royal Enfield Bullet 350 (Sold)
                    86' Ind-Suzuki Ax 100 (Sold)
                    03' HH Splendor

                    Comment

                    • #115
                      wrt the stickers i got i'm just saving up for a good paintjob.. i fear the stickers i picked up may not be original not sure how to find out.. if you guys are buying in bulk count me in.

                      a bit of advice wrt the piston. you need to be careful when you buy a piston.. what happened to me was the piston wasn't matched perfectly withthe block, which resulted in slight engine clatter, which is disheartening esp after the amount of running around i did for a new bore kit.. wat you'll have to do is check what type of block yours is, a single letter will be inscribed on the block either B Y or something. this will have to correspond coloured dot on the top of the piston. i think its B=blue Y=yellow

                      Comment

                      • #116
                        @ adi so wat did u do then to counter that problem????
                        http://www.youtube.com/watch?v=yjWXI8T2HUM
                        ---------------------------
                        07' Pulsar 200 DTS-i
                        99' Suzuki Shaolin
                        85' Royal Enfield Bullet 350 (Sold)
                        86' Ind-Suzuki Ax 100 (Sold)
                        03' HH Splendor

                        Comment

                        • #117
                          Go for Old CBZ's Front sprocket. Its got 14 teeth & fits into the gearbox..........
                          Quick Gun Shogun !

                          Comment

                          • #118
                            Originally posted by Nikhil Pereira View Post
                            @ adi so wat did u do then to counter that problem????
                            --WRT BORE AND PISTON KIT

                            unfortunately there was nothing i could do..

                            i knew it was going to be a problem, but i had no choice.. so i just went ahead with it.. the new bore is much better than the old one..
                            pulls decently.
                            during the run-in i was getting a mileage of over 50kmpl(keeping revs below 4000)

                            haven't checked mileage after run-in. during my recent trip i got a mileage of around 39~40 over a distance of around 700km on highway and really REALLY bad roads.. so i have nothing to complain about other than the sound of the piston clatter..

                            i've heard TVS sells(has sold in the past) their racing pistons(which i think are the last oversize- 1mm??) i'm not sure..
                            whether these exist and if we can get them is something i don't know..

                            i'm just letting you know about the piston matching problem because when you're searching for a piston you should know what you're looking for..

                            --WRT MIRRORS
                            what are you planning to do? i'm sure you'll get the samurai rectangular mirrors, but honestly i don't think they gell with the bike at all. unless you're trying to go for a total stock form.

                            Comment

                            • #119
                              @adi my bore indicates a neat B on top,

                              lol now take the rest as a joke,

                              My question to you is, wat does the blue and yellow denote
                              the first thing that came to my mind was my mum yelling nikhil go get the cylinder from the gas man down in the parking lot, and take the yellow gas book not the blue. . .

                              so ya adi in all seriousness wat is the meaning of this letter and ya wat did ure bore denote?
                              http://www.youtube.com/watch?v=yjWXI8T2HUM
                              ---------------------------
                              07' Pulsar 200 DTS-i
                              99' Suzuki Shaolin
                              85' Royal Enfield Bullet 350 (Sold)
                              86' Ind-Suzuki Ax 100 (Sold)
                              03' HH Splendor

                              Comment

                              • #120
                                Originally posted by Nikhil Pereira View Post
                                @adi my bore indicates a neat B on top,

                                lol now take the rest as a joke,

                                My question to you is, wat does the blue and yellow denote
                                the first thing that came to my mind was my mum yelling nikhil go get the cylinder from the gas man down in the parking lot, and take the yellow gas book not the blue. . .

                                so ya adi in all seriousness wat is the meaning of this letter and ya wat did ure bore denote?
                                lol

                                from what i got B on the bore denotes blue.. so the piston you buy will need to have a blue dot on the top(will be very clear and obvious marking).. that should be a perfect match

                                Comment

                                Previous 1 3 4 5 6 7 8 9 10 11 12 13 15 template Next
                                Working...
                                X
                                © xBhp.com 2026. All rights reserved.
                                Designed by xBhp