Since '02 xBhp is different things to different people. From a close knit national community of bikers to India's only motorcycling lifestyle magazine and a place to make like-minded biker friends. Join us

Axor
Magazine
Castrol Power 1

Look further to stay alive.

Our Partner

Announcement

Collapse
No announcement yet.

Random Questions regarding the RX series

Collapse
This is a sticky topic.
X
X
Collapse
 
  • Page of 89
  • Filter
  • Time
  • Show
Clear All
new posts
Previous 1 18 58 63 64 65 66 67 68 69 70 71 72 73 78 89 template Next
  • #1006
    Re: Random Questions regarding the RX series

    Originally posted by Mr.Boss View Post
    1. Speed alone doesn't decide a good run-in. What if running 50kmph on 2nd or 3rd gear? Oil quantity, AF ratio, frequency of engine running (time), Fuel quality, load on the engine, engine rpm and a lot more.
    2. Have you verified it? What was the teeth count?
    3. Around 110 kmph
    2)It has 71 teeth ( it hv some play between gear & clutch basket)
    Another question :i didnt change my front sprocket only change rear sprocket(34t) & chain set i forgot order front sprocket (ordered from indiaspares)

    Comment

    • #1007
      Re: Random Questions regarding the RX series

      Originally posted by Monish Bakre View Post
      2)It has 71 teeth ( it hv some play between gear & clutch basket)


      Another question :i didnt change my front sprocket only change rear sprocket(34t) & chain set i forgot order front sprocket (ordered from indiaspares)
      Usually chain sprocket kit comes with front/rear/sprockets, nuts,bolts and washer with chain and chain joint. I think you must have purchased each piece separately. Put 16t sprocket on the front. Whats the current teeth count on front sprocket? If its 15t, installing this 16 will give a little more top end.

      Also check the carbeurator tuning. Maybe the mechanic must have made the fuel mix little richer for the running in period. Tune it properly.
      Last edited by vimalnair4u; 11-25-2016, 05:44 PM.
      Happy & Safe Riding to All

      Comment

      • #1008
        Re: Random Questions regarding the RX series

        Originally posted by vimalnair4u View Post
        Usually chain sprocket kit comes with front/rear/sprockets, nuts,bolts and washer with chain and chain joint. I think you must have purchased each piece separately. Put 16t sprocket on the front. Whats the current teeth count on front sprocket? If its 15t, installing this 16 will give a little more top end.

        Also check the carbeurator tuning. Maybe the mechanic must have made the fuel mix little richer for the running in period. Tune it properly.
        Yes,can anyone suggest me which store is better for oine parts purchase i want to purchase clutch plates original one

        Comment

        • #1009
          Re: Random Questions regarding the RX series

          how to put wider front tyres for rx100 ?
          anything possible in stock rim ?

          Comment

          • #1010
            Re: Random Questions regarding the RX series

            Originally posted by Arun V Dev View Post
            how to put wider front tyres for rx100 ?
            anything possible in stock rim ?
            What size do you plan for?
            3.00x18 fits without any issues (with original steel mud guard or the plastic one from YBX)
            Nissan Sunny XVD | Toyota Corolla | Suzuki Ritz
            Yamaha RX135 4s-->5s | Yamaha RX100 | Yamaha RXG | Yamaha Ray | TVS Scooty Streak | Duke 390
            2000 Yamaha RX135 5s (Sold) | 1998 Yamaha RX135 4s (Sold) | 1997 Yamaha RXG (Sold) | 1994 Yamaha RX100 (Sold)

            Comment

            • #1011
              Re: Random Questions regarding the RX series

              2.50x18 or 2.75x18 is Ideal for RX. Anything beyond that will be overkill.
              Happy & Safe Riding to All

              Comment

              • #1012
                Re: Random Questions regarding the RX series

                Originally posted by vimalnair4u View Post
                2.50x18 or 2.75x18 is Ideal for RX. Anything beyond that will be overkill.
                How about 17" Rim with a wide tyre???

                Comment

                • #1013
                  Re: Random Questions regarding the RX series

                  Originally posted by Shreyas Rane View Post
                  How about 17" Rim with a wide tyre???

                  As boss mentioned, you can go up to 3.00. But its not required as RX is a light bike and riding comfort will also change. If you are going with 17" your speedo reading will have a slight difference.
                  Happy & Safe Riding to All

                  Comment

                  • #1014
                    Re: Random Questions regarding the RX series

                    Originally posted by vimalnair4u View Post
                    As boss mentioned, you can go up to 3.00. But its not required as RX is a light bike and riding comfort will also change. If you are going with 17" your speedo reading will have a slight difference.

                    What I'm saying is to decrease the rim size and put a slightly wider tyre....
                    Keeping the size of the whole assembly same as before but put a little bigger tyre to make the ride more comfortable.....

                    Comment

                    • #1015
                      Re: Random Questions regarding the RX series

                      Hello guys. Im planning to rebuild an Rxz which I will take from scrapyard and I will reincarnate it. Is it a good idea? Or I can just buy an owned Rxz and rebuild it?

                      Comment

                      • #1016
                        Re: Random Questions regarding the RX series

                        Help needed regarding rx135 block ... This in my bore condition what should i do install new sleeve or new block.. Acording to my observation port edges are sharp
                        Attached Files

                        Comment

                        • #1017
                          Re: Random Questions regarding the RX series

                          Originally posted by Mr.Boss View Post
                          What size do you plan for?
                          3.00x18 fits without any issues (with original steel mud guard or the plastic one from YBX)
                          can i use my rear tyre (3.00-18) as my front tyre?
                          it is ceat grip model.
                          any problems in using grip tyre instead of line thread for front application???

                          Comment

                          • #1018
                            Re: Random Questions regarding the RX series

                            Originally posted by Arun V Dev View Post
                            can i use my rear tyre (3.00-18) as my front tyre?
                            it is ceat grip model.
                            any problems in using grip tyre instead of line thread for front application???
                            Any specific reason to go for rear pattern in front? IMO a regular (Front pattern) 2.75x18 is more than sufficient.
                            To answer your question, Yes it is possible. there are people using the same in RX, but I couldn't comment on the advantages.
                            Nissan Sunny XVD | Toyota Corolla | Suzuki Ritz
                            Yamaha RX135 4s-->5s | Yamaha RX100 | Yamaha RXG | Yamaha Ray | TVS Scooty Streak | Duke 390
                            2000 Yamaha RX135 5s (Sold) | 1998 Yamaha RX135 4s (Sold) | 1997 Yamaha RXG (Sold) | 1994 Yamaha RX100 (Sold)

                            Comment

                            • #1019
                              Re: Random Questions regarding the RX series

                              Originally posted by Monish Bakre View Post
                              Help needed regarding rx135 block ... This in my bore condition what should i do install new sleeve or new block.. Acording to my observation port edges are sharp

                              You didnt mentioned about the pistion oversize currently running. You can go up to 2 mm oversize before going for a sleeve.
                              Happy & Safe Riding to All

                              Comment

                              • #1020
                                Re: Random Questions regarding the RX series

                                Originally posted by vimalnair4u View Post
                                You didnt mentioned about the pistion oversize currently running. You can go up to 2 mm oversize before going for a sleeve.
                                Sir i hv the basic knowledge .. 🙄🙄

                                Comment

                                Previous 1 18 58 63 64 65 66 67 68 69 70 71 72 73 78 89 template Next
                                Working...
                                X
                                © xBhp.com 2026. All rights reserved.
                                Designed by xBhp