Re: Random Questions regarding the RX series

The areas which you point at are transfer ports. (Compressed fuel air mixture from crank enters the bore via the intake port through these transfer ports)
It'd be better if you could post some pics of your bore as well.

Sent from my MI 3W using xBhp Connect mobile app

Re: Random Questions regarding the RX series

Parneet, you can change the charger that is located under the tank. (It looks like a heat exchanger on a motherboard :P)
If the problem persists, have your dyno checked.

Sent from my MI 3W using xBhp Connect mobile app

Re: My RX-100 Story, Ultimate Nostalgia!

Re: My RX-100 Story, Ultimate Nostalgia!

Hello bros,
I am going to paint my bike after 2 days, I have a question regarding color , here I am posting a bike pic which is taken by web. I have showd this color to painter but the color did not match to his color chart, in his color chat there was a color named Candy dark blur and the second was kashmiri dark blue both were metelick 2k paint. Pl suggest me what is the real color name ? What it is called, you can see the image of the bike below. Thanks

Re: My RX-100 Story, Ultimate Nostalgia!


If you can get to a Tata showroom, I believe the new zest has the same colour. Or you could check online for colour name bro from Tata zest website. Also a very slightly darker shade of the same is on the Volkswagen Vento I think.

Re: Random Questions regarding the RX series

Can u plz tell me what is the color code applied on your rx

----consecutive posts auto-merged-----

Thanks a lot [MENTION=72198]Balgi[/MENTION], I'll do that for sure.

Re: Random Questions regarding the RX series


The colour on my Rx100 is the 1986 stock peacock green-blue metallic colour bro, no change to that.

Re: Random Questions regarding the RX series

Hey everyone !!! My yamaha rxz 4 speed running fine but last few days she z giving me trouble the engine shuts off automatically and after few kicks with choke open it starts but the problem appears again after few km .. Can anyone help me out !! Cheers

Re: Random Questions regarding the RX series


Looks to me like the carb jets are blocked. Might be dirt in the petrol pipe. Also check air cleaner box for any blockages.
Hope this helps.
Cheers

Re: Random Questions regarding the RX series

[MENTION=65331]Mr.Boss[/MENTION] @Bibhu [MENTION=9171]yamdoot[/MENTION] [MENTION=31399]rxfan[/MENTION] @karthikdattag [MENTION=52680]rxdude[/MENTION] @kb100 [MENTION=22265]SriramEfunds[/MENTION] @all seniors
Sorry if missed anyone
I'm planning to rebuild my '92 rx100's engine.....
It's going to be a DIY so I need your help...
The main purpose is to replace all the case/crank bearings,oil seals,gaskets......
I've made a note of things to buy:
1) Gaskets,oil seals
2) Bearings
3) Tools required

The piston and block/cylinder are both in excellent condition but the bearing and oil seals have gone kaput....
Therefore, not going to change the piston and cylinder.........(will check the condition of rings and decide to change them accordingly)
I have a printed copy of the workshop manual...and also I'm going to follow instructions of this site
Two-Stroke Rebuild - Dirt Rider Magazine

I would like to know if I need to buy any special tools apart from those mentioned in the workshop manual...
Any other suggestions,precautions,or anything at all will be greatly appreciated......
P.S : I've kept INR 2000 aside for this......do I need to increase it or will it be sufficient
Talked to a spares guy (trusted one,helps me get genuine spares every time) he has given me an estimate of INR 500 for oil seals,gaskets,bearings.....

Thank you in advance.....
Sorry if I've missed anyone.....

Re: Random Questions regarding the RX series

1) I don't think any special tool other than what is mentioned in the workshop manual is required. Can you please post the snap from manual? (i haven't seen it for a long time)
2) Do take snaps at every possible angle while removing each & every part. This might help you during assembling
3) 500 for all the bearings, gaskets and oil seals? Impossible man. Price list is available in my thread, please have a look


Bearing kit alone should cost something close to 1k, packing kit around 200 INR, oil seal I don't remember exactly.

Re: Random Questions regarding the RX series

Ya sorry...my bad.....
Gaskets costed 180 INR
And Oil seals I'll get tomorrow.......
Bought 2 Crank bearings so far.... 285 each.....
But the bearings of con rod are worn out....
So I doubt the ones I've bought will be used....nevertheless, its always good to have spares....
Will start the dis-assembly tomorrow after 3:30 PM....(After my exam )
Don't know for how long will I work on it as planning to do it at my home......
BTW is it ok if I wash the case covers in mild detergent water and dry it with a blower then....??

Re: Random Questions regarding the RX series

to clean the innards of the crank case use paint thinner (nc thinner) and kerosine along with an old toothbrush, for scrapping cabon from the corners of the crank case get a few wooden spoon like thingies that you get along with ice creams , wear protective gloves while handling thinner , detergents wont cut it when you are dealing with carbon and gunk in crank cases even if you immerse them in detergent for a day or two ,

Re: Random Questions regarding the RX series

Thank you [MENTION=26930]kb100[/MENTION] for the advice......and as it happens to be I have a bottle or two of nc thinner lying around....had bought it to remove stains of ball pen ink from the wooden flooring....courtesy of my two dogs....[emoji12] [emoji12]..... Will post as many snaps as possible.... And thinking of starting it today.....if not...will surely start tomorrow....
BTW should i start a thread in DIY named RX100 ENGINE OVERHAUL (DIY)????

Re: Random Questions regarding the RX series

Detailed thread with sufficient snaps and step-by-by procedure should be a reference element for others