very neat work with the projectors...but battery!!!9 amp firstly will it fit?? and wont it mess up the electricals??

Its not a direct fit, i did some mod on battery box to fit it. As per the yamaha svc guy i can put 7 or 9amp battery if it fits and vola.... I am enjoying the light .

oh if there are no probs with the battery upgrade then im switching too sometime later!!! btw wer did u get those get those projectors from?? they dont look like those chinese one's :P

Now that is a neat one. I usually am in a bit of an oppose of these projectors or angel eye thingie but I like this one. I have heard that aftermarket lamps sometimes fiddle with the FI system. Is this true?

I'm working on this Saturday

Yes, these are not chinese one's. Even i dont like the those with angel ring and hid.
one of my friend got a lot of headlight assembly which has twin projector lenses (lower beam on left and upper beam on right side) and i m using it with a 55w bulb so no overload on wiring and battery.
Below is the image of low beam (single projector on)

Hi all,

I have just completed the first service of my R15.
Got it serviced in Raj Yamaha near thoraipaakam chennai with a bad experiance.

I had told them to fix the front doom vibartions but this was never done,
and there is noise from the front suspension when it moves up fast,
when you ride over a big speed braker with some speed, not sure what the problem is, i guess its the rubber holding the forks tight.
The water wash done was the worst ever, they delivered the bike with black grease patches everywhere.
Is it possible to fix the doom vibrations, please let me know if DIY tutorial exists.

I am also planning of getting a HID kit for my R15 and am a noob to lighting,
i have read several posts in this forum and am still confused.
Should i go for HID bulb alone or an HID with a project kit installed which will provide more visibility.

Does the philips HID kit come with a projector too?
Should i also rewind the coil? since the initial current used to charge the HID's is quite high.

If there's any place in chennai where i can get the HID installation done in chennai please let me know .

What is the tool required to remove the rivets in the R15 and also how should it be removed ?

Thanks for your help

If you are not planning to upgrade your battery, I would recommend single bixenon 35W 4300k/ 6000k HID. Tried and tested for long, no problems reported by anybody in YRC so far.

U mean only hid... Without projectors??? How much will it cost?? I mean a branded one. Plz recommend a good brand bro

A branded one (Philips) would cost ~ 6k IIRC. You can get China made ones at around 1.8k.
Just imagine how a single projector one side and normal reflectors on the other side look from the front :P

Teejay,

I still do not understand what do you mean by a single bixenon 35W 4300k/ 6000k HID.
What about the other bulb ?
Should it be a HID too or stick to stock, if it is stock will it not look odd on the high beam?
Am confused am also new to this lighting stuff

Guys sorry for the noobest question ever.....But seriously i dont know how to fix it and gives me some trouble.. After service i found that one part of My Rear Tyre is covered with some kind of sticky oil( i think its the Chain lube) ... I tried to wash it off and its not going even after water wash.. i feel like i lose some grip because of that bcz for the first time today my rear wheel locked under normal braking.Never happened before Plz help me on removing it...Can i use Dish washer like Pril to remove it?? Is it safe to use

I'd say always when you install HID a reflector must be used for the cutout of the beam, otherwise it would blind people ahead through the mirrors and mostly people on the oncoming lane and i guess you wouldn't want to be rude, do you? So please do the decent thing and go for projectors if your going to use HID lights.

PS: It is illegal in here to use HID without projectors.

Yes he means....1 hid and 1 stock....Will look a Bit odd though in high beam... Teejay why not 2 35W hid?? bcz even the stock is 35W + 35W in high beam

i am also facing the same problem,sticky oil on the rear rim unable to clean that.it is attracting more dust.any cleaner?