Announcement

**Sarvajit** · 11-19-2009, 06:50 PM

Originally posted by bala_racing View Post

It is always a recommended practice to change the piston and block as a set. There is no specific time to change that, it depends on the riding condition of the vehicle.

You need not change the carburetor as a whole. Clean and inspect the same for any fault. Mostly, the float (copper) will get damaged on long use. If required change the float and needle valve as a set. Costs around Rs.400/-.
BTW, 35-40 km/litre is less, have your bike completely serviced by an experienced mechanic.

Change the carb pin also alongwith the float!

**chief ashman** · 11-20-2009, 05:02 PM

Originally posted by bala_racing View Post

It is always a recommended practice to change the piston and block as a set. There is no specific time to change that, it depends on the riding condition of the vehicle.

You need not change the carburetor as a whole. Clean and inspect the same for any fault. Mostly, the float (copper) will get damaged on long use. If required change the float and needle valve as a set. Costs around Rs.400/-.
BTW, 35-40 km/litre is less, have your bike completely serviced by an experienced mechanic.

Originally posted by Sarvajit View Post

Change the carb pin also alongwith the float!

Thanks for your tips bala_racing & Sarvajit... I will try to get the needful done.

**bala_racing** · 11-20-2009, 05:06 PM

Originally posted by Sarvajit View Post

Change the carb pin also alongwith the float!

I think, the 'needle valve' I mentioned in my post and the 'carb pin' you are mentioning are one and the same

**remortr** · 11-25-2009, 12:37 AM

hi every body

i just now owend a fiero (2000) and i am rebulting see the pic.can any body tell that is their is availability

of the plastic parts such as tail assembely,air schoops,stickers,??

**bala_racing** · 11-25-2009, 12:58 PM

Originally posted by remortr View Post

i just now owend a fiero (2000) and i am rebulting see the pic.can any body tell that is their is availability

of the plastic parts such as tail assembely,air schoops,stickers,??

It should be available in the authorised showrooms or aftermarket dealers. I remember , I've seen a Fiero-Fx front fairing (new) in a shop in GP Road , Chennai.

BTW, are you rebuilding the bike yourself?

**remortr** · 11-26-2009, 03:12 AM

hi bala

yes i am rebuilding the bike my self to my taste

.if any one knows is their is any chance to fix rtr's speedometter to fiero,i am planing to change my wiring to rtr's one.pls help me .

**vinoopfredy** · 12-17-2009, 01:58 PM

Originally posted by remortr View Post

yes i am rebuilding the bike my self to my taste

.if any one knows is their is any chance to fix rtr's speedometter to fiero,i am planing to change my wiring to rtr's one.pls help me .

Hi,
I am planning to change the swing arm for my 2000 Fiero....
If i am changing the swing arm, what all things i will have to take care and
what all i will have to change.(change will be done by a mechanic).

1. Which bike swing arm can i use? Fiero F2/FX, Victor GLX??
2. Will the existing chain cover fit with the new one?
3. Will the chain , Sporocket have to be changed?(i hope chain have to be replaced with longer one(dont now) and hence sprocket too?

i am only a learner in bike mechanics. So please suggest.

My bike does well aprt from some engine noise. I hope reboring will do good.Bike has done 59000 km. It is a virgin engine. Will it give the same butter smooth style even after the reboring???

Kindly put your suggestions please.

**vinoopfredy** · 12-17-2009, 02:17 PM

Originally posted by remortr View Post

yes i am rebuilding the bike my self to my taste

.if any one knows is their is any chance to fix rtr's speedometter to fiero,i am planing to change my wiring to rtr's one.pls help me .

@remortr you can get all the plastics for Fiero. I am from chenai. I recently changed my tail piece, headlight dome, and the schoops. I see that your bike is black and so it is easy to get. For Red i found it difficult to get from chennai. I dont know whether the case is same for everyone.

Why are you changing the Fiero Wiring? for self start need.?

**remortr** · 12-17-2009, 03:37 PM

Originally posted by vinoopfredy View Post

@remortr you can get all the plastics for Fiero. I am from chenai. I recently changed my tail piece, headlight dome, and the schoops. I see that your bike is black and so it is easy to get. For Red i found it difficult to get from chennai. I dont know whether the case is same for everyone.

Why are you changing the Fiero Wiring? for self start need.?

hi buddy.just to fit the rtrs digital metter so that only i thinking about changing the wiring

.i will tell u a good suggestion to u r swing arm but pls wait for a day i am busy in some work i tell u tomorrow.Btw why u desided to change the arm? pls tel me

**nav75** · 12-17-2009, 05:25 PM

Originally posted by vinoopfredy View Post

1. Which bike swing arm can i use? Fiero F2/FX, Victor GLX??

Tried to go this way and can tell you that Victor swing arm is not a straight fit on Fiero.

**bprags** · 12-17-2009, 05:59 PM

Originally posted by vinoopfredy View Post

Hi,

1. Which bike swing arm can i use? Fiero F2/FX, Victor GLX??

Yes you can. I had the victors swing arm, right now using the GLX one. The F2/FX swing arm will be too long, for which you will have to change the rear wheel to a 17 inch one else it will hit the rear mud flap.

2. Will the existing chain cover fit with the new one?

No, you cannot use the existing chain cover, you will have to change depending on which bikes swing arm u r planning to use.

3. Will the chain , Sporocket have to be changed?(i hope chain have to be replaced with longer one(dont now) and hence sprocket too?

You can add a few links, but not advisable, simply go for a new one.

Kindly put your suggestions please.

Replies in bold.

**vinoopfredy** · 12-17-2009, 06:27 PM

Originally posted by remortr View Post

yes i am rebuilding the bike my self to my taste

.if any one knows is their is any chance to fix rtr's speedometter to fiero,i am planing to change my wiring to rtr's one.pls help me .

Originally posted by bprags View Post

Replies in bold.

all looks good
but why @nav told that victor swing arm cannot be fixed????

@bprags : i understoor the points which u expalined .. Are you telling that i have to go for a new chain, Or the entire chain sprocket assembly...?

@@@ sad that i got my chain cover painted recently... had a bit rust...
and wanted back its beauty.. ahahahha

Infact do you mean that the Suzuki fiero stock sprocket wont work out...?
can u make a rough cost estimation..

i hope ,
> chain sprocket assembly: </>1200
> swing arm will cost <> ??
> new chain cover ??

**vinoopfredy** · 12-17-2009, 06:37 PM

Originally posted by nav75 View Post

Tried to go this way and can tell you that Victor swing arm is not a straight fit on Fiero.

@Remortr : dear i planned to change the swing arm coz in needed more stability on my bike. I cam to that it it is done the ride quality and braking also can be improved. Suziki Fiero is having a short Swing arm, right. And so that too affects the wait balance, i suppose. That is teh main thing that is affecting the rear braking. I used to drive pretty fast mostly in 70 to 95(not able to reach hundred these days) Since i travel a pretty good distance through the OMR (straight stretch), i can feel the instability verymuch on full throtle. And with pillion rider it is a bit difficult in the chennai traffic. I also have a plan to increase the rear height.

@Nav : Not a straight fit. Then what all should i alter dear.
Should there be any change made for the static end of the swing arm.

thanks in advance...

**nav75** · 12-17-2009, 08:15 PM

Originally posted by vinoopfredy View Post

@Nav : Not a straight fit. Then what all should i alter dear.
Should there be any change made for the static end of the swing arm.

No idea what all needs to be changed as I dumped the idea of fitting the swing arm and stick to the stock one.

**vinoopfredy** · 12-18-2009, 01:17 PM

Originally posted by nav75 View Post

No idea what all needs to be changed as I dumped the idea of fitting the swing arm and stick to the stock one.

I think i will wait for Remortr

Announcement

Fiero/FieroF2/FieroFx

Comment

Comment

Comment

Comment

Comment

Comment

Comment

Comment

Comment

Comment

Comment

Comment

Comment

Comment

Comment